153crv

153 CRVwww.vishay.com Vishay BCcomponents

Revision: 18-Jun-13 1 Document Number: 28388

For technical questions, contact: [email protected] DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Aluminum CapacitorsSMD (Chip) Long Life Vertical

Fig. 1

FEATURES

• Polarized aluminum electrolytic capacitors, non-solid electrolyte, self healing

• SMD-version with base plate, vertical construction requiring minimum board space, lead (Pb)-free reflow solderable

• High CV per unit volume

• Long useful life: 2000 h to 3000 h at 105 °C

• Charge and discharge proof, no peak current limitation

• Supplied in blister tape on reel

• ATTENTION: For maximum safe soldering conditions refer to Fig. 4

• Material categorization: For definitions of compliance please see www.vishay.com/doc?99912

APPLICATIONS

• SMD technology, in compliance with RoHS

• Coupling, decoupling, smoothing, filtering, buffering, timing

• Telecommunications, general industrial, EDP, automotive, portable and lightweight equipment

MARKING

• Rated capacitance (in μF)

• Rated voltage (in V)

• Date code

• Black mark or “-” sign indicating the cathode (the anode is identified by bevelled edges)

PACKAGING

Supplied in blister tape on reel

QUICK REFERENCE DATADESCRIPTION VALUENominal case sizes(L x W x H in mm)

4.0 x 4.0 x 5.3 to 10 x 10 x 14

Rated capacitance range, CR 0.47 μF to 1000 μFTolerance on CR ± 20 %Rated voltage range, UR 6.3 V to 100 VCategory temperature range - 55 °C to + 105 °CEndurance test at 105 °C:Case sizes4.0 x 4.0 x 5.3 to 6.3 x 6.3 x 5.3 1000 hCase sizes 8.0 x 8.0 x 6.5 to 10 x 10 x 14 2000 hUseful life at 105 °C:Case sizes 4.0 x 4.0 x 5.3 to 6.3 x 6.3 x 5.3 2000 hCase sizes 8.0 x 8.0 x 6.5 to 10 x 10 x 14 3000 hUseful life at 40 °C; 1.3 x lR applied:Case sizes 4.0 x 4.0 x 5.3 to 6.3 x 6.3 x 5.3 200 000 hCase sizes 8.0 x 8.0 x 6.5 to 10 x 10 x 14 300 000 hShelf life at 0 V, 105 °C 1000 h

Based on sectional specification IEC 60384-18/CECC 32300

Climatic category IEC 60068 55/105/56

175 TMP175 °C

solid SMD

140 CRH125 °C

153 CRV

150 CRZ

High temp.

Low Z

http://www.vishay.com





Table 1

Note• Detailed tape dimensions see section “PACKAGING”.

SELECTION CHART FOR CR, UR, AND RELEVANT NOMINAL CASE SIZES (L x W x H in mm)

CR(μF)

UR (V)

6.3 10 16 25 35 50 63 100

0.47 - - - - - 4.0 x 4.0 x 5.3 - -

1.0 - - - - - 4.0 x 4.0 x 5.3 - -

2.2 - - - - - 4.0 x 4.0 x 5.3 - -

3.3 - - - - - 4.0 x 4.0 x 5.3 - -

4.7 - - - - 4.0 x 4.0 x 5.3 5.0 x 5.0 x 5.3 - -

10 - - 4.0 x 4.0 x 5.3 - 5.0 x 5.0 x 5.3 6.3 x 6.3 x 5.3 - -

22 4.0 x 4.0 x 5.3 - 5.0 x 5.0 x 5.3 - 6.3 x 6.3 x 5.3 8.0 x 8.0 x 6.5 - -

33 - 5.0 x 5.0 x 5.3 - 6.3 x 6.3 x 5.3 8.0 x 8.0 x 6.5 8.0 x 8.0 x 10 - 10 x 10 x 14

47 5.0 x 5.0 x 5.3 - 6.3 x 6.3 x 5.3 8.0 x 8.0 x 6.5 - 8.0 x 8.0 x 10 - -

1006.3 x 6.3 x 5.3 - 8.0 x 8.0 x 6.5 8.0 x 8.0 x 10 - 10 x 10 x 10 10 x 10 x 14 -

- - - - - - - -

220 - 8.0 x 8.0 x 10 10 x 10 x 10 - - - - -

330 8.0 x 8.0 x 10 10 x 10 x 10 - 10 x 10 x 14 - - - -

470 10 x 10 x 10 - 10 x 10 x 14 - - - - -

680 - 10 x 10 x 14 - - - - - -

1000 10 x 10 x 14 - - - - - - -

TAPE AND REEL DIMENSIONS in millimeters AND PACKAGING QUANTITIES

CASE CODE PITCHP1

TAPE WIDTHW

TAPE THICKNESST2

REELDIAMETER

PACKAGING QUANTITYPER REEL

0405 8 12 5.8 380 2000

0505 12 12 5.8 380 1000

0605 12 16 5.8 380 1000

0807 12 16 6.8 380 1000

0810 16 24 11.3 380 500

1010 16 24 11.3 380 500

1014 16 24 14.8 330 250






Fig. 2 - Dimensional outline

Table 2

MOUNTINGThe capacitors are designed for automatic placement on to printed-circuit boards.Optimum dimensions of soldering pads depend amongst others on soldering method, mounting accuracy, print layout and/or adjacent components.For recommended soldering pad dimensions, refer to Fig. 3 and Table 3.

SOLDERINGSoldering conditions are defined by the curve, temperature versus time, where the temperature is that measured on the soldering pad and on top of the case during processing.For maximum conditions refer to Fig. 4. Maximum 2 runs with pause of minimum 30 min between.Any temperature versus time curve which does not exceed the specified maximum curves may be applied.AS A GENERAL PRINCIPLE, TEMPERATURE AND DURATION SHALL BE THE MINIMUM NECESSARY REQUIRED TO ENSURE GOOD SOLDERING CONNECTIONS. HOWEVER, THE SPECIFIED MAXIMUM CURVES SHOULD NEVER BE EXCEEDED.

Fig. 3 - Recommended soldering pad dimensions

Table 3

DIMENSIONS in millimeters AND MASSNOMINAL CASE SIZE

L x W x H CASE CODE Lmax. Wmax. Hmax. Ø D Bmax. S MASS(g)

4.0 x 4.0 x 5.3 0405 4.5 4.5 5.5 4.0 0.8 1.0 0.135.0 x 5.0 x 5.3 0505 5.5 5.5 5.5 5.0 0.8 1.4 0.206.3 x 6.3 x 5.3 0605 6.8 6.8 5.5 6.3 0.8 2.0 0.308.0 x 8.0 x 6.5 0807 8.6 8.6 6.8 8.0 0.8 2.3 0.508.0 x 8.0 x 10 0810 8.6 8.6 10.5 8.0 1.1 3.1 1.0010 x 10 x 10 1010 10.6 10.6 10.5 10.0 1.1 4.7 1.3010 x 10 x 14 1014 10.6 10.6 14.3 10.0 1.2 4.5 1.50

0.4 ± 0.2

W B

S 0.3 max.

H

L D

RECOMMENDED SOLDERING PAD DIMENSIONS in millimetersCASE CODE a b c

0405 2.6 1.6 1.00505 3.0 1.6 1.40605 3.5 1.6 1.90807 4.0 1.6 2.10810 3.5 2.5 3.01010 4.0 2.5 4.01014 4.3 2.5 4.0

b

aca






Fig. 4 - Maximum temperature load during reflow soldering measured on capacitors soldering pad and top of the case

Note• Temperature measuring point on top of the case and terminals max. 2 runs with pause of 30 min in between

REFLOW SOLDERING CONDITIONS

PROFILE FEATURESCASE CODE 0405 TO 0605

CASE CODE 0807 TO 1010

CASE CODE 1014 63 V

CASE CODE 1014 100 V

Max. time from 25 °C to Tpeak 240 s 240 s 300 s 270 s

Max. ramp-up rate to 150 °C 3 K/s 3 K/s 3 K/s 3 K/s

Max. time from 150 °C to 200 °C (t1) 120 s 120 s 150 s 120 s

Ramp up rate from 200 °C to Tpeak 0.5 K/s to 3 K/s 0.5 K/s to 3 K/s 0.5 K/s to 3 K/s 0.5 K/s to 3 K/s

Max. time from 200 °C to 217 °C, (t2) 20 s 20 s 60 s 60 s

Max. time above TLiquidus (217 °C), (t3) 60 s 60 s 90 s 60 s

Max. time above 230 °C (t4) 30 s 20 s 40 s 30 s

Peak temperature Tpeak 250 °C 240 °C 250 °C 240 °C

Max. time above Tpeak minus 5 °C 5 s 5 s 5 s 10 s

Max. ramp-down rate from TLiquidus 6 K/s 6 K/s 6 K/s 6 K/s

t1

200

150

217

230

TPeak

time (s)

T (°C)

t2

t3

t4






Note• Unless otherwise specified, all electrical values in Table 4 apply

at Tamb = 20 °C, P = 86 kPa to 106 kPa, RH = 45 % to 75 %.

ORDERING EXAMPLE

Electrolytic capacitor 153 CRV series

100 μF/25 V; ± 20 %

Nominal case size: 8 mm x 8 mm x 10 mm; taped on reel

Ordering code: MAL215376101E3

Former 12NC: 2222 153 76101

Table 4

ELECTRICAL DATASYMBOL DESCRIPTION

CRRated capacitance at 100 Hz or 120 Hz,tolerance ± 20 %

IR Rated RMS ripple current at 100 Hz or 120 Hz, 105 °C

IL2 Max. leakage current after 2 min at UR

tan Max. dissipation factor at 100 Hz or 120 Hz

ESR Equivalent series resistance at 100 kHz

ELECTRICAL DATA AND ORDERING INFORMATION

UR(V)

CR(μF)

NOMINALCASE SIZE

L x W x H (mm)

IR105 °C(mA)

IL22 min(μA)

tan 100 Hz

ESR100 kHz

()

ORDERING CODEMAL2153.......

6.3

22 4.0 x 4.0 x 5.3 21 3.0 0.30 8 73229E3

47 5.0 x 5.0 x 5.3 36 3.0 0.30 4 73479E3

100 6.3 x 6.3 x 5.3 61 6.3 0.30 2 73101E3

330 8.0 x 8.0 x 10 180 21 0.30 0.5 73331E3

470 10 x 10 x 10 320 30 0.30 0.3 73471E3

1000 10 x 10 x 14 400 63 0.24 0.24 73102E3

10

33 5.0 x 5.0 x 5.3 31 3.3 0.26 4 74339E3

220 8.0 x 8.0 x 10 180 22 0.26 0.5 74221E3

330 10 x 10 x 10 320 33 0.26 0.3 74331E3

680 10 x 10 x 14 380 68 0.19 0.24 74681E3

16

10 4.0 x 4.0 x 5.3 16 3.0 0.22 8 75109E3

22 5.0 x 5.0 x 5.3 28 3.5 0.22 4 75229E3

47 6.3 x 6.3 x 5.3 47 7.5 0.22 2.2 75479E3

100 8.0 x 8.0 x 6.5 110 16 0.22 1.2 75101E3

220 10 x 10 x 10 320 35 0.22 0.3 75221E3

470 10 x 10 x 14 370 75 0.16 0.25 75471E3

25

33 6.3 x 6.3 x 5.3 44 8.3 0.16 2.2 76339E3

47 8.0 x 8.0 x 6.5 110 12 0.16 1.2 76479E3

100 8.0 x 8.0 x 10 180 22 0.16 0.5 76101E3

330 10 x 10 x 14 300 83 0.14 0.27 76331E3

35

4.7 4.0 x 4.0 x 5.3 14 3.0 0.13 8 70478E3

10 5.0 x 5.0 x 5.3 23 3.5 0.13 4 70109E3

22 6.3 x 6.3 x 5.3 50 7.7 0.13 2.2 70229E3

33 8.0 x 8.0 x 6.5 110 12 0.13 1.2 70339E3

50

0.47 4.0 x 4.0 x 5.3 5 3.0 0.12 12 71477E3

1.0 4.0 x 4.0 x 5.3 7 3.0 0.12 12 71108E3

2.2 4.0 x 4.0 x 5.3 10 3.0 0.12 12 71228E3

3.3 4.0 x 4.0 x 5.3 12 3.0 0.12 12 71338E3

4.7 5.0 x 5.0 x 5.3 17 3.0 0.12 6 71478E3

10 6.3 x 6.3 x 5.3 26 5.0 0.12 3 71109E3

22 8.0 x 8.0 x 6.5 110 11 0.12 1.2 71229E3

33 8.0 x 8.0 x 10 180 17 0.12 0.5 71339E3

47 8.0 x 8.0 x 10 180 24 0.12 0.5 71479E3

100 10 x 10 x 10 320 50 0.12 0.3 71101E3

63 100 10 x 10 x 14 240 63 0.09 0.34 78101E3

100 33 10 x 10 x 14 170 33 0.07 1.3 79339E3






CAPACITANCE (C)

Fig. 5 - Typical multiplier of capacitance at 100 Hz or 120 Hzas a function of ambient temperature

EQUIVALENT SERIES RESISTANCE (ESR)

Fig. 6 - Typical ESR as a function of frequency at 20 °C

DISSIPATION FACTOR (tan )

Fig. 7 - Typical dissipation factor (tan ) at 100 Hz or 120 Hzas a function of ambient temperature

IMPEDANCE (Z)

Fig. 8 - Typical impedance as a function of frequency at 20 °C

ADDITIONAL ELECTRICAL DATAPARAMETER CONDITIONS VALUE

Voltage

Surge voltage IEC 60384-18, subclause 4.14 Us 1.15 x UR

Reverse voltage IEC 60384-18, subclause 4.16 Urev 1 V

Current

Leakage current After 2 min at UR IL2 0.01 x CR x UR or 3 μA, whichever is greater

Inductance

Equivalent series inductance (ESL)Case codes 0405 to 0605 Typ. 10 nH

Case codes 0807 to 1014 Typ. 15 nH

- 40 - 20 0 20 40 60 80 100 120

1.1

1.0

0.9

0.8

0.7

CC0

Tamb (°C)C0 = Capacitance at 20 °C

1

2

2

1

Curve 1: 1 µF, 50 VCurve 2: 100 µF, 6.3 V

f (kHz)

ESR(Ω)

102

10

1

0.1

0.1 1 10 102 103

Curve 1: 22 μF, 6.3 VCurve 2: 22 μF, 16 VCurve 3: 22 μF, 25 V

1

2

3

10

1

0.1

0.01

0.001

Tamb (°C)

2

1

tan δ Curve 1: 1 µF, 50 VCurve 2: 100 µF, 6.3 V

- 60 - 40 - 20 0 20 40 60 80 100 120

f (kHz)

Z (Ω)

102

10

1

0.1

0.1 1 10 102 103

1

23

Curve 1: 22 µF, 6.3 VCurve 2: 22 µF, 16 VCurve 3: 22 µF, 25 V






RIPPLE CURRENT AND USEFUL LIFE

Fig. 9 - Multiplier of useful life as a function of ambient temperature and ripple current load

Table 5

MULTIPLIER OF RIPPLE CURRENT (IR) AS A FUNCTION OF FREQUENCYFREQUENCY

(Hz)IR MULTIPLIER

UR = 6.3 V TO 16 V UR = 25 V OR 35 V UR = 50 V TO 100 V

50 or 60 0.80 0.80 0.80

100 or 120 1.00 1.00 1.00

300 1.10 1.15 1.20

1000 1.15 1.25 1.35

3000 1.20 1.35 1.45

10 000 1.25 1.40 1.50

3.8

3.7

3.6

3.5

3.4

3.3

3.2

3.0

2.8

2.6

2.4

2.2

2.0

1.8

1.6

1.4

1.2

1.00.80.50.0

3.1

40 50 60 70 80 90 100 110

lifetime multiplier

(1)

200

10060

1.0

30

150

20

6.04.0

2.01.5

128.0

3.0

Tamb (°C)

IAIR

CCC206

IA = Actual ripple current at 100 Hz or 120 Hz

IR = Rated ripple current at 100 Hz or 120 Hz

at 105 °C

For case codes 0405 to 1010 max. IA/IR = 2.4(1) Useful life at 105 °C and IR applied:

Case codes 0405 to 0605: 2000 h

Case codes 0807 to 1014: 3000 h






Table 6

TEST PROCEDURES AND REQUIREMENTSTEST PROCEDURE

(quick reference) REQUIREMENTSNAME OF TEST REFERENCE

MountingIEC 60384-18,subclause 4.3

Shall be performed prior to tests mentioned below;reflow soldering;for maximum temperature load refer to chapter “Mounting”

C/C: ± 10 %

tan spec. limit

IL2 spec. limit

EnduranceIEC 60384-18/CECC 32300,subclause 4.15

Tamb = 105 °C; UR applied;1000 h, case codes 0405 to 06052000 h, case codes 0807 to 1014

C/C: ± 20 %

tan 2 x spec. limit

IL2 spec. limit

Useful lifeCECC 30301,subclause 1.8.1

Tamb = 105 °C; UR and IR applied;2000 h, case codes 0405 to 06053000 h, case codes 0807 to 1014

C/C: ± 50 %

tan 3 x spec. limit

IL2 spec. limit

no short or open circuit

total failure percentage: 1 %

Shelf life(storage at high temperature)

IEC 60 384-18/CECC 32 300,subclause 4.17

Tamb = 105 °C; no voltage applied;1000 hAfter test: UR to be applied for 30 min, 24 h to 48 h before measurement

For requirements see “Endurance test” above


Legal Disclaimer Noticewww.vishay.com Vishay

Revision: 02-Oct-12 1 Document Number: 91000

DisclaimerALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and allliability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particularpurpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typicalrequirements that are often placed on Vishay products in generic applications. Such statements are not binding statementsabout the suitability of products for a particular application. It is the customer’s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application. Parametersprovided in datasheets and/or specifications may vary in different applications and performance may vary over time. Alloperating parameters, including typical parameters, must be validated for each customer application by the customer’stechnical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainingapplications or for any other application in which the failure of the Vishay product could result in personal injury or death.Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Pleasecontact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or byany conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category PolicyVishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill thedefinitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Councilof June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Freerequirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make referenceto the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21conform to JEDEC JS709A standards.

153crv

Documents