ceb1059
TRANSCRIPT
-
7/29/2019 CEB1059
1/6
250-C20 CEB-1COMMERCIAL ENGINE BULLETIN overhau
PAGE 1 OF October 14,
CECOPOWERTURBINEGOVERNOR, QUADRANTAND SHAFT ASSEMBLY-REWORKPLANNING INFORMATION:EFFECTIVITY: All of the following power turbine governor assemblies:
DDA Part No, CECO Part No.6851468 1041OOA66886409 104100A86851407* 10~4500Al6886410* 104500A3* Multi-engine applications
REASON: To increase life of the quadrant and shaft assembly sealthereby eliminating fuel leakage around the quadrant andshaft assembly.DESCRIPTION: The width of the two quadrant and shaft assemb ly O-ringgrooves is increased to accommodate new O-ring sealswith the additional Teflon back-up rings. Following re-work, the governor assembly is reidentified.COMPLIANCE: Modification is recommended at first repair or overhaul(whichever occurs first) following parts ava ilability.
I APPROVAL: FAA-DER Approved.MANPOW ER: It is estimated that approximately one additional man-hour will be required at time of overhaul.PARTS AVAILABILITY: New CECO P/N Nomenclature 2x.
101306** Quadrant and Shaft 1Assembly101302-013 Packing, Preformed 2MS28774-013 Ring, Back-up 2** P/N 100619 Quandrant and Shaft Assemblies may bereworked to P/N 101306 configuration.
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
-
7/29/2019 CEB1059
2/6
250-C20 CEB-1059OverhaulPage 2COMMERCIAL ENGINE BULLETIN
CECO POWER TURBINE GOVERNOR, QUADRANTAND SHAFT ASSEMBLY-REWORK
INTERCHANGEABILITY:All changes in this bulletin must be accomplishedsimultaneously.
TOOLING: NoneWEIGHT AND BALANCE: NoneREFERENCES:DDA CW-1176 and (X-1220CECO PC0 74-91 and PSIL 73-17
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
-
7/29/2019 CEB1059
3/6
250-C20 CEB-10OverhaulPage 3COMMERCIAL ENGINE BULLETINCECO POWER TURBINE GOVERNOR, QUADRANTAND SHAFT ASSEMBLY-REWORK
ACCOMPLISHMENT INSTRUCTIONS:At first repair or overhau l following parts availability, rework power turbinegovernor P/N 100619 Quadrant and Shaft Assem bly to a.ccommodate two newP/N 101302-013 O-rings with MS28774-013 Back-up R i:ugs.I. Disassemble Governor and Rework Quadrant and Shaft Assemb ly.
A. Disassemble governor and inspect parts in accordance with the 250-C20Overhaul Manual (Appendix Bl).B. Rework serviceable P/N 100619 Quadrant and Shaft Assem bly as follows:
1. Increase O-ring groove width by machining in accordance w ithFigure 1.2. Reidentify Quadrant and Shaft Assem bly as P/N 10130 6 by taggingor marking part container.
C. If P/N 100619 Quadrant and Shaft Assem bly cannot be reworked, re-place with P/N 10130 6 Quadrant and Shaft Assemb ly.H. Reassemble Governor.
A. Reassem ble governor in accordance with the 250-C20 Overhaul Manual(Appendix Bl) except install two new P/N 101302 -013 Packings and twonew P/N MS28774-013 Back-up Rings on P/N 10130 6 Throttle Shaftas shown on Figure 2.B. Reidentify the power turbine governor assembly using l/8-inch numberand letter punches as follows:
Old DDA P/N Old CECO P/N New DDA P/N New CECO P/N-6886409 104100A8 6890905 104100A96886410 104500A3 6890906 104500A46851468 104100A6 6891455 104100A9-A86851407 1045OOAl 6891456 104500A4-A3C. Record comp liance w ith 250 CEB-1059 in the Eng ine Assem bly (whitepages) Modification Record, Part Ill of the Eng ine Log Book.
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
-
7/29/2019 CEB1059
4/6
250-C20 CEB-1059OverhaulPage 4
COMMERCIAL ENGINE BULLETINCECO POWER TURBINE GOVERNOR, QUADRANTAND SHAFT ASSEMBLY-REWORK
BREAK EDGES .002-.015
GROO VE .448-.452 DIAX. 149-,159 WIDE -.005-.OlSRIN BOTTOM CORNERS2 PLACES
REWORK OF QUADRANT AND SHAFT ASSEMBLYFIGURE 1
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
-
7/29/2019 CEB1059
5/6
250-C20 CEB-1059OverhaulPage 5COMMERCIAL ENGINE BULLETINCECO POWER TURBINE GOVERNOR, QIJADRANTAND SHAFT ASSEMBLY-REWORK
BACK -UP RING
\ PACKl ,NG /
ASS EMB LY OF PACKINGS AND BACK-U:P RINGSON QUADRANT AND SHAFT ASSEMB LYFIGURE 2
Rolls-Royce Proprietary Data Uncontrolled Printed Copy
-
7/29/2019 CEB1059
6/6
250-C20 CEB-1059OverhaulPage 6
COMMERCIAL ENGINE BULLETINCECO POWER TURBINE GOVERNOR, QUADRANTAND SHAFT ASSEMBLY-REtiORK
MATERIAL INFORMATION:NewP/N &ty Nomenclature Old P/N6890905 1 Governor Assy, Power 6886409(CECO Turbine (CECO104100AS) 104100A8)6890906 1 Governor Assy, Power 6886410(CECO Turbine (CECO1045OOA4) 104500A3)6891455 1 Governor Assy, Power 6851468(CECO Turbine (CECO104100AS-A8) 104100A6)6891456 1 Governor Assy, Power 6851407(CECO Turbine (CECO104500A4-A3) 104500Al)101306 1 Quadrant & Shaft Assy 100619101302-013 2 Packing, Preformed MS9021-13MS28774-013 2 Ring, Back-up --m-m--
Qty Disposition-1 1
1 1
1 1
1 1
1 12 23
Stock Disposition Notes:1 Rework and reidentify2 Scrap removed part3 Added
I!. 0. DavidsonService ManagerAircraft EnginesMJK/bsc
Rolls-Royce Proprietary Data Uncontrolled Printed Copy