ls882c_1

Upload: cinematic3006

Post on 10-Apr-2018

219 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/8/2019 LS882C_1

    1/3

    - 2 -

    SPECIFICATIONS

    1. LCD CHARACTERISTICSType : TFT SXGA LCDSize : 18.1inch (45.97cm)Pixel Pitch : 0.2805(H) x 0.2805(V)Pixel Format : 1280 x 1024 pixels (SXGA)

    RGB Stripe ArrangementColor Depth : 8-bit, 16,581,375 colorsActive Video Area : 413mm x 333mmSurface Treatment : Anti-Glare, Hard Coating (3H)Backlight Unit : Four-CCFL (Cold Cathode

    Fluorescent Lamp)

    2. OPTICAL CHARACTERISTICS2-1. Viewing Angle by Contrast Ratio 10

    Left : 80min. , Right : 80min.Top : 80min. , Bottom : 80min.

    2-2. Luminance : 170 cd/m 2 (min)

    2-3. Angle at Half LuminanceLeft : 45min. , Right : 45min.Top : 45min. , Bottom : 45min.

    2-4. Contrast Ratio : 300typ.

    3. SIGNAL (Refer to the Timing Chart)3-1. Sync Signal

    Type : Separate, TTL, Positive/NegativeComposite, TTL, Positive/Negative

    SOG (Sync On Green)Digital

    3-2. Video Input Signal1) Type : R, G, B Analog2) Voltage Level : 0~0.714 V

    a) Color 0, 0 : 0 Vp-pb) Color 7, 0 : 0.467 Vp-pc) Color 15, 0 : 0.714 Vp-p

    3) Input Impedance : 75

    3-3. Operating FrequencyHorizontal : 30 ~ 80kHzVertical : 56 ~ 85Hz

    4. POWER SUPPLY

    4-1. Power AdaptorInput : AC 100~240V, 50/60Hz , ~2.0 - 1.0AOutput : DC 12V 5.8A

    4-2. Power Consumption

    5. ENVIRONMENT

    5-1. Operating Temperature: 10C~35C (50F~95F)(Ambient)

    5-2. Relative Humidity : 10%~80%(Non-condensing)

    5-3. Altitude : 0~10,000ft (3,030m)

    6. DIMENSIONS (with TILT/SWIVEL)

    Width : 434 mm (17.09'')Depth : 235 mm (9.25'')

    Height : 443 mm (17.44'')

    7. WEIGHT (with TILT/SWIVEL)

    Net. Weight : 9.0kg (20.65 lbs)Gross Weight : 12.3kg (27.12 lbs)

    8. USBUpstream : 1 port, Downstream : 4 portSpeed : High-12Mbps, Low-1.5Mbps

    MODE

    POWER ON (NORMAL)

    STAND-BY

    SUSPEND

    OFF

    POWER OFF

    H/V SYNC

    ON/ON

    OFF/ON

    ON/OFF

    OFF/OFF

    -

    POWER CONSUMPTION

    less than 70 W

    less than 5 W

    less than 5 W

    less than 5 W

    less than 5 W

    LED COLOR

    GREEN

    AMBER

    AMBER

    AMBER

    OFF

    VIDEO

    ACTIVE

    OFF

    OFF

    OFF

    -

  • 8/8/2019 LS882C_1

    2/3

    - 3 -

    Signal Connector Pin Assignment

    Pin Signal (D-Sub)12345678

    Red VideoGreen VideoBlue VideoGroundGroundRed GroundGreen GroundBlue Ground

    Pin Signal (D-Sub)9

    101112131415

    N.C.Sync.GroundGroundSDAH. Sync.V. Sync.SCL

    11

    615

    15

    10

    NOTENo. 5 Pin have to ground on the PC side.

    Pin Signal (DVI-I)123456789

    101112131415

    T. M. D. S. Data2-T. M. D. S. Data2+T. M. D. S. Data2/4 ShieldT. M. D. S. Data4-T. M. D. S. Data4+DDC Clock

    DDC DataAnalog Vertical Sync.T. M. D. S. Data1-T. M. D. S. Data1+T. M. D. S. Data1/3 ShieldT. M. D. S. Data3-T. M. D. S. Data3++5V PowerGround (return for +5V,H. Sync. and V. Sync.)

    Pin Signal (DVI-I)

    1 8917 24

    16

    C1

    C4C3

    C2C5

    161718192021222324C1C2C3C4C5

    Hot Plug DetectT. M. D. S. Data0-T. M. D. S. Data0+T. M. D. S. Data0/5 ShieldT. M. D. S. Data5-T. M. D. S. Data5+

    T. M. D. S. Clock ShieldT. M. D. S. Clock+T. M. D. S. Clock-Analog RedAnalog GreenAnalog BlueAnalog H. Sync.Analog Ground

    T. M. D. S. (Transition Minimized Differential Signaling)

    15pin VGA Connector

    DVI-I Connector (Digital/Analog)

  • 8/8/2019 LS882C_1

    3/3

    - 4 -

    WARNING FOR THE SAFETY-RELATED COMPONENT.

    There are some special components used in LCDmonitor that are important for safety. These parts aremarked on the schematic diagram and thereplacement parts list. It is essential that these criticalparts should be replaced with the manufacturer sspecified parts to prevent electric shock, fire or otherhazard.

    Do not modify original design without obtaining writtenpermission from LG or you will void the original partsand labor guarantee.

    TAKE CARE DURING HANDLING THE LCD MODULE

    WITH BACKLIGHT UNIT.

    Must mount the module using mounting holes arranged

    in four corners. Do not press on the panel, edge of the frame strongly

    or electric shock as this will result in damage to thescreen.

    Do not scratch or press on the panel with any sharpobjects, such as pencil or pen as this may result indamage to the panel.

    Protect the module from the ESD as it may damage theelectronic circuit (C-MOS).

    Make certain that treatment person s body aregrounded through wrist band.

    Do not leave the module in high temperature and inareas of high humidity for a long time.

    The module not be exposed to the direct sunlight.

    Avoid contact with water as it may a short circuit withinthe module.

    If the surface of panel become dirty, please wipe it offwith a softmaterial. (Cleaning with a dirty or rough clothmay damage the panel.)

    WARNING

    BE CAREFUL ELECTRIC SHOCK !

    If you want to replace with the new backlight (CCFL) orinverter circuit, must disconnect the AC adapter

    because high voltage appears at inverter circuit about650Vrms.

    Handle with care wires or connectors of the invertercircuit. If the wires are pressed cause short and mayburn or take fire.

    PRECAUTION

    CAUTION

    Please use only a plastic screwdriver to protect yourselffrom shock hazard during service operation.

    CAUTION

    There is two backlight, must distinguish betweenthe top (upper) and the bottom (lower), and becareful of treatment it.

    MTBF (Mean Time Between Failure) of a backlightis about 30,000 hours.

    IF BRIGHTNESS OF THE LCD MODULE DARKEN,REPLACE THE BACKLIGHT ONE OR ALL.

    Backlight Ass y(P/N: 6913TZZ002A)