ti_07_1996_30
TRANSCRIPT
-
7/30/2019 TI_07_1996_30
1/3
7HFKQLFDO,QIRUPDWLRQ
%ORZHU 67,+/%* 6HULHV(GJHUV 67,+/)& 6HULHV
67,+/)& 6HULHV%UXVKFXWWHUV 67,+/)6 6HULHV
67,+/)6 6HULHV
(ODVWR6WDUWVSHFLDODFFHVVRU\
A newly developed ElastoStart is available as aspecial accessory for the above models withimmediate effect. It greatly enhances operatorcomfort during starting.
No changes to the rewind starter are necessaryto retro-fit the ElastoStart. Only the installationprocedure itself varies slightly from that used forthe standard starter grip (see service notes).
000TI007
KN
&RQVWUXFWLRQ
The construction of the new ElastoStart gripdiffers from that of the version already installed in
a number of chainsaw models (see TI 29.92).
The ElastoStart consists of the following parts:
Grip Cap Sleeve Helical spring Washer Starter rope
1
2
3
4
5
6
5
000TI008
KN
Tensile
force
Travel (Hand)
ElastoStartStandard grip
-
7/30/2019 TI_07_1996_30
2/3
)XQFWLRQ
In the relaxed position, the sleeve (3), helical spring(4) and washers (5) are held in place in the grip bythe stop lug (7).
During cranking, the force applied by the operatorpulling the grip is transmitted via the grip (1), lowerwasher (5), helical spring (3), upper washer (5) andsleeve (3) to the rope (6).As this force is opposed by engine compression thehelical spring is compressed. The peak forces whichoccur on each compression stroke are cushioned bythe spring.
The forces which occur at the grip after the firstcompression stroke are practically uniform.This greatly enhances starting comfort.
If the starting force exceeds a specific level (determin-ed by the helical spring), the spring is fullycompressed and cranking effort is then transmitteddirectly from the grip to the rope.
6HUYLFHQRWHV
Repairs are limited to replacement of the starterrope. A faulty ElastoStart can only be replaced
as a complete assembly.
,QVWDOOLQJ(ODVWR6WDUWZLWKVWDUWHUURSH
Thread the starter rope through the rope guidebushing IURPRXWVLGH the starter housing.
Thread the rope into the rope rotor and secureit with a VLPSOHRYHUKDQG knot.
7
1
3
4
5
6
5
000TI0
09
KN
000TI010KN
7HFKQLFDO,QIRUPDWLRQ3DJH
-
7/30/2019 TI_07_1996_30
3/3
5HSODFLQJ(ODVWR6WDUWVWDUWHUURSH
Ease the cap off the starter grip.
Remove remaining rope from the grip and
rope rotor. Fit the starter rope 0000 195 8200 in the same
way as the standard rope, but only secure it inthe grip with a VLPSOHRYHUKDQG knot.
Refit cap in the grip.
Starter rope 0000 195 8200 must be used toguarantee correct operation of the ElastoStart.
000TI011KN
5HSODFHPHQWSDUWVIRU(ODVWR6WDUW
Pos. Part Name Part No. Rem.
ElastoStart;including item 1:
1 Starter rope 3 x 800 mm
0000 190 3400
0000 195 8200
Last Technical Information on models:
BG 72 03.95FC 72 46.94, worldwide 47.94, USAFC 44 47.94, USA onlyFS 36, 40 17.94, worldwide 47.94, USAFS 44 39.95FS 72 12.95FS 74, 76 39.95
Andreas Stihl - D1/MTK-naTechnical Documentation 5775 1996 Andreas Stihl
7HFKQLFDO,QIRUPDWLRQ3DJH