ua748
TRANSCRIPT
-
7/27/2019 ua748
1/8
s INPUT OFFSET VOLTAGE : 3mV max. OVERTEMPERATURE
s FREQUENCY COMPENSATION WITH ASINGLE 30pF CAPACITOR (C1)
s OPERATION FROM 5V to 15Vs LOW POWER CONSUMPTION :
50mW AT 15Vs
CONTINUOUS SHORT-CIRCUIT PROTEC-TIONs OPERATION AS A COMPARATOR WITH
DIFFERENTIAL INPUTS AS HIGH AS 30Vs NO LATCH-UP WHEN COMMON-MODE
RANGE IS EXCEEDEDs SAME PIN CONFIGURATION AS THE
LM101A
DESCRIPTION
The UA748 is a general purpose operational am-plifier built on a single silicon chip. The resultingclose match and tight thermal coupling gives lowoffsets and temperature drift as well as fast recov-ery from thermal transients.
s Short-circuit protections Offset voltage null capabilitys Large common-mode and differential voltage
rangess Low power consumptions No latch-upThe unity-gain compensation specified makes thecircuit stable for all feedback configurations, evenwith capacitive loads. However, it is possible tooptimize compensation for best high frequencyperformance at any gain. The low power dissipa-tion permits high voltage operation and simplifiespackaging in full-temperature range systems.
ORDER CODE
N = Dual in Line Package (DIP)D = Small Outline Package (SO) - also available in Tape & Reel (DT)
PIN CONNECTIONS (top view)
Part Number Temperature RangePackage
N D
UA748C 0C, +70C
UA748I -40C, +105C
UA748M -55C, +125C
Example : UA748CN
NDIP8
(Plastic Package)
DSO8
(Plastic Micropackage)
1
2
3
4
8
6
5
7
1 - Offset null 1/frequency compensation2 - Inverting input3 - Non-inverting input
4 - VCC-
5 - Offset null 26 - Output
7 - VCC+
8 - Frequency compensation
UA748PRECISION SINGLE OPERATIONAL AMPLIFIER
-
7/27/2019 ua748
2/8
UA748
SCHEMATIC DIAGRAM
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter UA748M UA748I UA748C Unit
VCC Supply voltage 22 V
Vid Differential I nput Voltage 30 V
Vi Input Voltage 15 V
Ptot Power Dissipation 1)
1. Power dissipation must be considered to ensure maximum junction temperature (Tj) is not exceeded.
500 mW
Output Short-circuit Duration InfiniteToper Op erating Free-air Temperature Range -55 to +1 25 -40 to +105 0 to +70 C
Tstg Storage Temperature Range -65 to +150 C
-
7/27/2019 ua748
3/8
UA748
ELECTRICAL CHARACTERISTICS
VCC
= 15V, Tamb
= +25C, C1 = 30pF (unless otherwise specified)
Symbol ParameterUA748I/M UA748C
UnitMin. Typ. Max. Min. Typ. Max.
Vio
Input Offset Voltage (Rs 10k)
Tamb = +25C
Tmin Tamb Tmax
0.7 23
2 7.510
mV
Iio
Input Offset CurrentTamb = +25C
Tmin Tamb Tmax
1.5 1020
2 5070
nA
Iib
Input Bias CurrentTamb = +25C
Tmin Tamb Tmax
25 7510
70 250300
nA
Avd
Large Signal Voltage Gain (Vo = 10V, RL = 2k)Tamb = +25C
Tmin Tamb Tmax
5025
100 2515
100 V/mV
SVR
Supply Voltage Rejection Ratio (Rs 10k)
Tamb = +25C
Tmin Tamb Tmax
8080
96 7070
96 dB
ICC
Supply Current, no loadTamb = +25C
Tmin Tamb Tmax
1.8 33
1.8 33
mA
Vicm
Input Common Mode Voltage Range (VCC = 20V)
Tamb = +25C
Tmin Tamb Tmax
1515
1515
V
CMRCommon Mode Rejection Ratio (RS
10k)
Tamb = +25C
Tmin Tamb Tmax
8080
96 7070
96 dB
IOS Output short Circuit Current 10 30 50 10 30 50 mA
Vopp
Output Voltage Swing (VCC = 15V)
Tamb = +25C RL = 10k
RL = 2k
Tmin Tamb Tmax RL = 10k
RL = 2k
12101210
1413
12101210
1413 V
SRSlew Rate 1)
Vi = 10V, RL = 2k, CL = 100pF, unity Gain
1. May be improved up to 10V/s in inverting amplifier configuration .
0.25 0.5 0.25 0.5V/s
trRise Time
Vi
= 20mV, RL
= 2k, CL
= 100pF, unity Gain 0.3 0.3s
KovOvershoot
Vi = 20mV, RL = 2k, C L = 100pF, unity G ain 5 5%
Zi Input Impedance (VCC = 15V) 1.5 4 1.5 4 M
Ro Output Resistance (VCC = 15V) 75 75
GBPGain Bandwith Product
Vi =10mV, RL = 2k, CL = 100pF, f =100kHz 0.5 1 0.5 1MHz
THDTotalH armonic Distortion
f =1kHz, Av =20dB, RL =2k, Vo =2Vpp, CL = 100pF 0.015 0.015%
DIio
Input Offset Current Drift25C TmaxTmin Tamb Tmax
1020
100200
1020
300600
pA/C
DVio
Input Offset Voltage Drift
Tmin Tamb Tmax 3 15 6 30 V/
C
-
7/27/2019 ua748
4/8
UA748
-
7/27/2019 ua748
5/8
UA748
SINGLE POLE COMPENSATION
-
7/27/2019 ua748
6/8
UA748
PACKAGE MECHANICAL DATA
8 PINS - PLASTIC DIP
Dim.Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
A 3.32 0.131
a1 0.51 0.020
B 1.15 1.65 0.045 0.065
b 0.356 0.55 0.014 0.022
b1 0.204 0.304 0.008 0.012
D 10.92 0.430
E 7.95 9.75 0.313 0.384
e 2.54 0.100
e3 7.62 0.300
e4 7.62 0.300
F 6.6 0260
i 5.08 0.200L 3.18 3.81 0.125 0.150
Z 1.52 0.060
-
7/27/2019 ua748
7/8
UA748
PACKAGE MECHANICAL DATA
8 PINS - PLASTIC MICROPACKAGE (SO)
Dim.Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.25 0.004 0.010
a2 1.65 0.065
a3 0.65 0.85 0.026 0.033
b 0.35 0.48 0.014 0.019
b1 0.19 0.25 0.007 0.010
C 0.25 0.5 0.010 0.020
c1 45 (typ.)
D 4.8 5.0 0.189 0.197
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 3.81 0.150
F 3.8 4.0 0.150 0.157
L 0.4 1.27 0.016 0.050
M 0.6 0.024
S 8 (max.)
b
e3
A
a2
s
L
C
E
c1a3
b1
a1
DM
8 5
1 4
F
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for theconsequences of use of such information nor for any infringement of patents or other rights of third parties which may resultfromits use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specificationsmentioned in this publication are subject to change without notice. This publication supersedes and replaces all informationpreviously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices orsystems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
2001 STMicroelectronics - Printed in Italy - All Rights ReservedSTMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - Fr ance - Germany - Hong Kong - India - Israel - Italy - Japan - MalaysiaMalta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States
http://www.st.com
-
7/27/2019 ua748
8/8
This datasheet has been download from:
www.datasheetcatalog.com
Datasheets for electronics components.
http://www.datasheetcatalog.com/http://www.datasheetcatalog.com/http://www.datasheetcatalog.com/http://www.datasheetcatalog.com/